Pre-Taped Masking Film for Car Painting – 3 Pack Painters Plastic Sheeting with Automotive Tape and Drape, Paint Plastic Covering Cars, Appliance, Windows and Furniture Protection (17 Inch) 17 Inch
Pre-Taped Masking Film for Car Painting – 3 Pack Painters Plastic Sheeting with Automotive Tape and Drape, Paint Plastic Covering Cars, Appliance, Windows and Furniture Protection (17 Inch)
The problem every painter knows: Standard plastic sheeting is too stiff for curved body panels. Paint slides down the film and drips. Removal kicks flakes back onto your fresh coat. JMI BASIC white masking film solves all three. ① Corona Treatment – Paint stays on the film The surface is restructured at a molecular level so spray paint bonds directly to the film. No sliding. No dripping. No flaking on removal. ② Flexible Film – Follows every curve Soft, pliable material conforms to door edges, bumper curves, fender arches, and mirror housings without lifting or gapping. One person. One pass. Complete seal. ③ Electrostatic Cling – Sticks on contact No extra tape needed to hold the film to panels. The electrostatic charge grips the surface automatically, even on vertical and overhead areas. ④ Professional Grade Tape – Built for the Booth Pre-attached yellow crepe tape is engineered to perform where standard tapes fail. Tape Specifications: Tape Thickness: 0.135mmAdhesive Type: Rubber- basedAdhesion Strength: 4 N/25mm widthTensile Strength: 90 N/25mm widthElongation: 9%Heat Resistance: 80°C / 176°F – 60 minutes Holds firm through full spray booth heat cycles. Peels off in one clean motion. Zero adhesive residue on panels, trim, glass, or painted surfaces. What you get: Corona treated – automotive professional gradeFlexible film conforms to curved body panelsElectrostatic cling grips all surfaces automaticallyHeat resistant tape 80°C / 176°F for 60 minutesRubber-based adhesive – strong hold, clean releaseZero adhesive residue on all surfacesCompatible with solvent and waterborne automotive paintsWorks for interior painting, construction, and DIYTear-resistant and waterproof plastic film Available in 18", 26", 35", 59", 94" size pack For professionals and DIYers who won't redo the same job twice.
Product Features
- [CORONA TREATED PAINT LOCKS ONTO FILM, NOT THE FLOOR] JMI BASIC white masking film uses corona treatment to bond overspray paint directly to the film surface. No dripping. No flaking during removal. No paint landing back on your fresh finish. The standard for professional auto body shops worldwide.
- [HEAT RESISTANT TAPE UP TO 80C / 176F FOR 60 MINUTES NO RESIDUE] Pre-attached yellow crepe tape withstands spray booth temperatures for up to 60 minutes without softening, bleeding, or leaving adhesive residue. Peels off cleanly in one smooth motion no sticky traces on panels, trim, or glass. Rubber-based adhesive ensures strong hold during the job and clean release after.
- [ELECTROSTATIC CLING] GRIPS PANELS ON CONTACT, NO EXTRA TAPE Electrostatically charged film sticks to car doors, hoods, fenders, and bumpers the moment it touches the surface. Stays flat through an entire spray session. Zero gaps. Zero bleed-through. Zero mid-job adjustments.
- [ANTI-FLAKE & CLEAN FINISH] - Unlike cheap plastic, dried paint sticks to our film like a magnet. This prevents dried paint dust from falling onto your fresh coat when removing the film.
- [AUTOMOTIVE FIRST. WORKS EVERYWHERE ELSE TOO] Engineered for collision repair, spray booth painting, and auto refinishing. Equally effective for interior wall painting, construction masking, window protection, and furniture coverage. Tear-resistant, waterproof, zero adhesive residue on all surfaces.
- [TAPE ALREADY ATTACHED 2 in 1 FULL PANEL COVERED IN 60 SECONDS] Yellow crepe masking tape is pre-bonded to the film edge. No fumbling with separate rolls. Position, unfold, done. One person can mask an entire vehicle in minutes. Works with HVLP spray guns, rattle cans, and paint robots.