IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset
IndusTec 30 AMP 12V DC - Momentary Motor Polarity Control Reversing Rocker Switch (On)-Off-(On) 4 pin Double Pole Double Throw for 5th Wheel Tongue Trailer RV Power Jack Automatic Reset
Hook any 2 side by side to supply and others to motorThe DC motor will reverse one way then the other with switch operationThe switch will return to center off position when releasedGreat for easy fix solution for Motor Homes Boats, windows, Robotics, Kids science projects and many more.Used for tow winch devices in some casesUsed on many tongue and 5th wheel jacks Read more IndusTec 30 Amp Momentary Motor Polarity Reverse Rocker With 12 AWG 65/30 tinned switch amperage rating 30 Amps at 12 VDC 15 Amps at 24 Wiring Instuctions Hook 2 center terminals to 12 or 24 volt power supply then other 2 to motor Cut Out Fits standard 0.83 X 1.46 Cut out About 21mm X 37mm Seal Has rubber rubber seal to help keep water out of panel Action 3 Position spring return to center off position Markings None 30 Amp Momentary Rocker with Pigtail leads 30 Amp Latching Rocker with Wires 30 Amp Momentary Rocker 4 pc pin 30 Amp Locking Rocker 4 Quick Conects 20 Amp resetting Rocker and wires 20 Amp Rocker 4 1/4 .250 Pins Has 30 amp wire ✓ ✓ ✓ Switch rated for 30a at 12 VDC ✓ ✓ ✓ Will spring to off when released ✓ ✓ ✓ ✓ Stays in last position placed when released ✓ ✓ Has panel sealing gasket under lip ✓ ✓ ✓ ✓ ✓ ✓ Maintained Polarity Toggle Momentary Polarity Toggle 10 AMP Auto Reset Polarity Toggle 10 AMP Latching Polarity Toggle Maintained Polarity Toggle Momentary Polarity Toggle Has 12 AWG 65/30 strand Tinned boat Grade Wire ✓ ✓ Has 12 guage Audio Stranded Wire ✓ ✓ Automatic Resetting Spring Return to Off ✓ ✓ ✓ Ratded for 20 Amps At 12 VDC ✓ ✓ ✓ ✓ Rated for 10 Amps at 12 VDC ✓ ✓ Silver Alloy Plated Copper Contacts ✓ ✓ ✓ ✓ Momentary Medium polarity Rocker Maintained Medium Polarity Rocker Waterproof Resetting 10 AMP Latching Reversing Rocking IndusTec Intermediate Rocker Switch 2 Pole 2 Throw 3 Position 6 Pin IndusTec Intermediate Rocker Switch 2 Pole 2 Throw 3 Position 6 Pin Latching Has 12 guage Audio Stranded Wire ✓ ✓ ✓ Has 18 guage AWG Stranded Wire ✓ Retains Positions ✓ ✓ Returns to off when released ✓ ✓ 3 position auto 6 Pin 3 Position latch Pin 2 position 6 pin 2 position 6 screw 3 position 6 screw auto 2 pos SPST latch 2 screws Latches in place ✓ ✓ ✓ ✓ Automatically returns to Off ✓ ✓ 3 Positions ✓ ✓ ✓ 2 Positions ✓ ✓ ✓ Switches for Dummies To clear up voltage ratings on switches Most manufacturers print a voltage rating on the switch at the factory. They normally print the highest voltage at which the switch should be used for on a continuous basis under normal conditions. Now this is a very controversial statement because not everyone's normal is the same. Lets just say dust and debris not visible, Moisture not high and no extreme temperatures that would affect the insulative or mechanical properties of the components. It needs to be said here that the switch is good for any voltage below that rating all the way to zero volts. Under the same conditions no matter whose definition of normal you use. So if the connecting device says 600V on it it is also good for 12 VDC or 24 VDC or 125 VAC and 250 VAC and so on at any value between 0 and 600 AC or DC. To clear up Amperage ratings on switches That does not mean that the amperage rating on the switch applies to all voltages and types of current. As a matter of fact it only is supposed to apply to the voltage and type stated on the switch. If you apply ohms law to voltage and amperage it would indicate that if the voltage were half the amperage could double. I Current (amperage) = Voltage divided by Resistance. Changing the voltage of the circuit does not change the resistance. However that is not true with alternating current. So you can not use ohms law to determine the amperage value for AC. And there are many more mechanical factors for both DC and AC that have profound affects on arching outside the scope of this discussion. Like materials,speed, pressure, sliding, bouncing, and so on. So it is very important to reach out to the manufacturer of any switch for amperage ratings for the voltage you need in the circuit. Maintained and Momentary explained A Maintained switch is noted several ways in different industries On Off On or Latched or Latching or Locking It is going to Latch Lock in position you or someone else places it. Used for non jogging operations like pumps fans or lights A momentary switch denoted in several ways also is (On) Off (On) or Resetting or automatic reset or springing This term means it will return spring reset to a position (usually off) when you release it. For jogging operations like lift hoist winch or door What does Pole and Throw refer to Consider pole to indicate the number of Isolated (individual) Inputs. Throw would be the number of outputs for each pole. Do not confuse the throws with positions. Any single throw switch can only have 2 positions On Off if you think about it. But a double throw switch can have 2 or 3 positions. If a double throw switch has 3 positions it is sometimes referred to as On Off On, and will probably have off as one of the positions. ( usually in the center ). If a double throw switch has only 2 positions then it will always have the input connected to one of the outputs and will not have an off position for all outputs at same time . This is sometimes referred to as On On.
Product Features
- DPDT Rating: 30 amps at 12 Volt DC and 15 Amps at 24 Volts DC. Has four prong post with built in jumper bars for Polarity Reverse. Size: This Reverse Polarity Switch with 1.47''X0.83''(37.4X21mm) Cut-out Size and 1.736''X0.95''(44.1X24.13mm) Housing Size. Three Position. Wires not included. Rubber external gasket cover under mounting lip to protect panel from dirt, dust and rain and help keep panel dry. Not waterproof. Push Button.
- This is a momentary electrical system switch used for jogging or inching operations. A DPDT switch is equivalent to two SPDT switches. Dual Operation. It routes two separate circuits, connecting each of two inputs to one of two outputs. The position of the switch determines the number of ways in which two contact can be routed. Always make sure you are using a switch and wire sufficient to handle the load you are carrying. In higher draw applications, a relay may be needed.
- Can be used to replace SWT-ROC-MOM-4W, 129-PR-MOM. Atwood Power Jack numbers: 80236, 80511, 80515, 80530, 80509, 80524. Direct Replacement for Atwood Part# 87570 and Lippert Components part number 226023. Other part numbers: KCD2-7-223-4P-X, KCD2-7-223B
- Can be used to replace Drum, Rotary, Cable, Adapter, Relay. Also a great replacement for RV or Electric Trailer Power, Travel Trailers, Tongue Jack Stabilizer, Fifth Wheels Jacks, and slideout Power awning switches. Great for Travel Trailers such as: Keystone, Grand Design, and Coachman. Snap In Switch Easy install. 30A Momentary Automatic Reset action, Resetting returns to off when released. Simply connect power and ground and two DC motor leads and the switch will reverse the motor direction
- Our heavy duty switches are durable and reliable. Used in Auto, Car Accessories, Camper, Hitch, Truck, Boat, Motorcycle, ATV, UTV, Airplane, Aviation, Robotics, Automotive Parts, Automation System, Industrial, Factory, Machine Work, Marine, Do it yourself DIY Projects, Winch, LED Light Bar, Sound Systems, Awning, Bilge Pump, Dash Panel Controls, Jack Hoist Actuator, Lift, Stabilizers, Electronics, Liftgate, Motorized Windows Up / Down, Door Open / Close, Electrical Devices, and much more!