{"id":7811353411764,"title":"CONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box) 1\/4\" x 1-3\/4\"","handle":"confast-1-4-x-1-3-4-concrete-screws-410-stainless-steel-phillips-flat-countersunk-with-concrete-drill-bit-for-anchoring-to-masonry-block-or-brick-50-per-box-1-4-x-1-3-4","description":"\u003ch3\u003eCONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eApplications The anchor is made from 410 Stainless Steel, and is Silver\nClimaseal Coated. This anchor is designed for use in Concrete, Block, and\nBrick. Environment The anchor is designed for use in a Moist environment. Head\nStyle The anchor is a Flat Countersunk Phillips head and is designed to\nprevent the head from protruding above the surface of the item being attached.\nHole Diameter\/Bit Diameter The anchor requires a 3\/16\" hole to be drilled in\nthe base material (Concrete, Block, and Brick). The hole should be drilled\nwith carbide tipped bit that meets ANSI standards and used in a hammer drill.\nDriver Required A 3 phillips bit is required for driving the anchor into the\nbase material. Diameter of Anchor The diameter of the anchor is 1\/4\". Length\nAnchor The length of the anchor is 1-3\/4\" Thread Length The length of the\nthreads on the anchor is 1-3\/4\" in length. Minimum Embedment The minimum\nanchor embedment into the concrete is 1\". Therefore, the anchor must be\ninstalled so that a minimum of 1\" of the anchor is embedded into the concrete.\nMaximum Fixture Thickness The maximum fixture thickness or the maximum\nthickness of the material being fastened for a anchor is 1\/4\". This will\nensure that the minimum embedment of 1\" will be met. Fixture Hole Diameter The\nhole in the fixture or material being fastened must be larger than the\ndesignated diameter of the anchor. The 1\/4\" diameter anchor requires the hole\nin the fixture to be 5\/16\". Spacing between Anchors Each anchor must be spaced\na minimum distance of 4\" from each other when measured center to center. Edge\nDistance It is very important not to install the anchor any closer than 3\"\nfrom an unsupported edge of the concrete.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eBIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost\u003c\/li\u003e\n \u003cli\u003eHEX HEAD--Can be driven with Hex Driver\u003c\/li\u003e\n \u003cli\u003eSELF-TAPPING-Taps threads directly into masonry and requires no other anchor\u003c\/li\u003e\n \u003cli\u003eDIAMOND POINT-Easier to drive the screw to save time\u003c\/li\u003e\n \u003c\/ul\u003e","published_at":"2024-08-08T09:53:47+10:00","created_at":"2024-08-06T02:43:49+10:00","vendor":"CONFAST","type":"Concrete Screws","tags":["industrial_Aug2024_update"],"price":20100,"price_min":20100,"price_max":20100,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":43457156153524,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B09HK37M5P","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"CONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box) 1\/4\" x 1-3\/4\"","public_title":null,"options":["Default Title"],"price":20100,"weight":381,"compare_at_price":null,"inventory_management":"shopify","barcode":"820274004661","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/auspowers.com\/cdn\/shop\/files\/41yKQxeA8GL.jpg?v=1722876234","\/\/auspowers.com\/cdn\/shop\/files\/71JqsAvBMVL.jpg?v=1722876234","\/\/auspowers.com\/cdn\/shop\/files\/51HIW8MPiyL.jpg?v=1722876234"],"featured_image":"\/\/auspowers.com\/cdn\/shop\/files\/41yKQxeA8GL.jpg?v=1722876234","options":["Title"],"media":[{"alt":"[Australia - AusPower] - CONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box) 1\/4\" x 1-3\/4\" ","id":30570376495284,"position":1,"preview_image":{"aspect_ratio":4.173,"height":422,"width":1761,"src":"\/\/auspowers.com\/cdn\/shop\/files\/41yKQxeA8GL.jpg?v=1722876234"},"aspect_ratio":4.173,"height":422,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/files\/41yKQxeA8GL.jpg?v=1722876234","width":1761},{"alt":"[Australia - AusPower] - CONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box) 1\/4\" x 1-3\/4\" ","id":30570376528052,"position":2,"preview_image":{"aspect_ratio":1.0,"height":2560,"width":2560,"src":"\/\/auspowers.com\/cdn\/shop\/files\/71JqsAvBMVL.jpg?v=1722876234"},"aspect_ratio":1.0,"height":2560,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/files\/71JqsAvBMVL.jpg?v=1722876234","width":2560},{"alt":"[Australia - AusPower] - CONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box) 1\/4\" x 1-3\/4\" ","id":30570376560820,"position":3,"preview_image":{"aspect_ratio":1.778,"height":720,"width":1280,"src":"\/\/auspowers.com\/cdn\/shop\/files\/51HIW8MPiyL.jpg?v=1722876234"},"aspect_ratio":1.778,"height":720,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/files\/51HIW8MPiyL.jpg?v=1722876234","width":1280}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003eCONFAST 1\/4\" x 1-3\/4\" Concrete Screws 410 Stainless Steel Phillips Flat Countersunk with Concrete Drill Bit for Anchoring to Masonry, Block or Brick (50 per Box)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eApplications The anchor is made from 410 Stainless Steel, and is Silver\nClimaseal Coated. This anchor is designed for use in Concrete, Block, and\nBrick. Environment The anchor is designed for use in a Moist environment. Head\nStyle The anchor is a Flat Countersunk Phillips head and is designed to\nprevent the head from protruding above the surface of the item being attached.\nHole Diameter\/Bit Diameter The anchor requires a 3\/16\" hole to be drilled in\nthe base material (Concrete, Block, and Brick). The hole should be drilled\nwith carbide tipped bit that meets ANSI standards and used in a hammer drill.\nDriver Required A 3 phillips bit is required for driving the anchor into the\nbase material. Diameter of Anchor The diameter of the anchor is 1\/4\". Length\nAnchor The length of the anchor is 1-3\/4\" Thread Length The length of the\nthreads on the anchor is 1-3\/4\" in length. Minimum Embedment The minimum\nanchor embedment into the concrete is 1\". Therefore, the anchor must be\ninstalled so that a minimum of 1\" of the anchor is embedded into the concrete.\nMaximum Fixture Thickness The maximum fixture thickness or the maximum\nthickness of the material being fastened for a anchor is 1\/4\". This will\nensure that the minimum embedment of 1\" will be met. Fixture Hole Diameter The\nhole in the fixture or material being fastened must be larger than the\ndesignated diameter of the anchor. The 1\/4\" diameter anchor requires the hole\nin the fixture to be 5\/16\". Spacing between Anchors Each anchor must be spaced\na minimum distance of 4\" from each other when measured center to center. Edge\nDistance It is very important not to install the anchor any closer than 3\"\nfrom an unsupported edge of the concrete.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eBIT INCLUDED IN EACH BOX-Proper bit equals improved holding values and reduced cost\u003c\/li\u003e\n \u003cli\u003eHEX HEAD--Can be driven with Hex Driver\u003c\/li\u003e\n \u003cli\u003eSELF-TAPPING-Taps threads directly into masonry and requires no other anchor\u003c\/li\u003e\n \u003cli\u003eDIAMOND POINT-Easier to drive the screw to save time\u003c\/li\u003e\n \u003c\/ul\u003e"}