ZKTOOL Power Probe Short Circuit Tester Tester Light 6V-24V DC Tools Component Activation Electrical Tester Polarity Identify Continuity Tester with Indicator Light,Long Probe, Alligator Clip.
ZKTOOL Power Probe Short Circuit Tester Tester Light 6V-24V DC Tools Component Activation Electrical Tester Polarity Identify Continuity Tester with Indicator Light,Long Probe, Alligator Clip.
Upgrade performance Circuit Tester It can test the polarity of voltage, the continuity of relays and diodes, fuses and circuits, check lights, check motors, track and locate short circuits, test for poor grounding, test the polarity of cables and plugs, and measure 2V to 24V DC Voltage etc. Test polarity Connect the red clip to the positive terminal of the car battery. Connect the black clip to the negative terminal of the car battery. Touch the tip of the probe to the negative (-), and the LED should light up green. Test polarity Connect the red clip to the positive terminal of the car battery. Connect the black clip to the negative terminal of the car battery. Touch the tip of the probe to the negative (-), and the LED should light up green. Read more Can test different parts of the vehicle Working voltage: 6-24VDC Cable length: about 4r overload protection: 7A (when the current exceeds 7A, this item will be disconnected The current is automatic. ) Weight; about 200 grams Material type: plastic and stainless steel TEM length: 225 mm/8.85 inches Lead length: about 4M/157.Sinch Item width: 30 mm/1.18 inch Read more Attention item 1. Do not use the item around explosive gas, vapor or dust. When the power is turned on: When pressed (or shaken), the battery current is directly conducted to the tip, which may Sparks can be caused when touching the ground or certain circuits 2. This machine is not suitable for 11o/220V household current, only for DC6~24V system 3. After the vehicle inspection is completed, correctly restore all connections -s which3. Do not use under AC voltage 4. Always follow the instructions and procedures indicated in the service of the vehicle you disconnected from. Trying to disconnect the electrical 5 before any part or subsystem. For safety reasons, do not touch any dangerous parts of the vehicle with your hands. Do not touch any live conductors with your hands or skin. 6. Do not use if damaged 8. Some parts of the vehicle work under low voltage, and they cannot withstand the relative voltage of the article. To avoid damage to these components, do not use 9. Before driving, please make sure that the vehicle is safe and reliable. The project directly or indirectly applies voltage lv. 10. Do not use this item while driving. Polarity test and continuity test Polarity test: This tool can test the uncertain polarity of contacts in the vehicle circuit. This tool can test the uncertain polarity of contacts in the vehicle circuit. Unfold the wire. Connect the red clip to the positive terminal of the car battery. Connect the black clip to the negative terminal of the car battery. Touch the tip of the probe to the positive (+), and the LED should light up red. Touch the probe tip to the negative (-), the LED should light up green. Continuity test Expand the leader. Connect the red clip to the positive terminal of the vehicle battery. Connect the black clip to the negative terminal of the vehicle battery. Connect the auxiliary ground wire to one side of the wire under test, and connect the probe tip to the other side. When there is continuity, the LED will light up green. If the LED does not light up, there is no continuity. Test the components outside the vehicle electrical system and test the components in the vehicle electrical system Test the components outside the vehicle's electrical system Expand the leader. Connect the red clip to the positive terminal of the vehicle battery. Connect the black cip to the negative terminal of the vehicle battery. Connect the auxiliary ground to the negative terminal of the component under test. Press the button (the side where the LED is lit red to touch the probe tip to the positive pole of the component under test to activate the component. If the LED turns green and the buzzer sounds, please stop the test and check whether the component is defective or the component’s The rated current is higher than this tester. Test components in the vehicle's electrical system Expand the leader. Connect the red clip to the positive terminal of the vehicle battery. Dip black into the negative terminal of the vehicle battery. When the S control switch of the element is on the positive side of the element, press the button to the "-" side, and the LED will light up in red. Touch the probe tip to the positive terminal of the assembly. The component will be activated. Jumper operation When the negative terminal of some components needs to be well grounded for large current to flow, this tester is a good tool for testing its grounding. Expand the leader. Connect the red clip to the positive pole! Car battery. Connect the black clip to the negative terminal of the vehicle battery. Press the button to the side, the LED should light red and provide positive voltage. Then let the probe touch the negative terminal of the element as quickly as possible, the LED indicator turns green, and the power indicator lights up. vri meaus itiswelded. If not teLED Remaining Short circuit tracking and positioning Short circuit tracking and positioning Expand the leader. Connect the red cip to the positive terminal of the vehicle battery. Connect the black clip to the negative terminal of the vehicle battery. Press the button to the'"-" side, the LED should light up red and provide a positive voltage. Remove the blown fuse from the fuse box and start tracking from the two terminals of the fuse socket. Use the probe tip to quickly touch the wire. If the LED lights up green and is accompanied by a buzzer, there is a short circuit or an overload component on this side. Please pay attention to the color or identification code of this wire. Follow the wire as much as possible along the wire harness. Locate the color-coded wire in the harness and expose it. Cut the wire. Follow the wire in the direction of the short circuit and repeat his process until you find the short circuit. If there is a separate check if the components are good.
Product Features
- Function: It can test the polarity of voltage, the continuity of relays and diodes, fuses and circuits, check lights, check motors, track and locate short circuits, test for poor grounding, test the polarity of cables and plugs, and measure 2V to 24V DC Voltage etc.
- Contains: 1 x Power Scan, 1 x Probe Tip, 1 x Battery Hookup Clips, 1 x User Manual, 2 x red clips. Lead length: about 4M / 157.Sinch, which is convenient for you to measure the polarity of the vehicle's various orientation circuits.
- Application: 1 Clamp the red clip on the positive pole of the car battery, 2 Clamp the black clip on the negative pole of the car battery, 3 Connect the car power probe to the bad point of 6-24V DC. You can conduct positive and negative battery currents to the probe by shaking the power switch forward or backward. The cable length is about 4m. The device has short-circuit protection, when the current exceeds 7A, the device will automatically cut off the current.
- Features:This tool has two obvious reminders, sound and flash, so you can still use it even in low light conditions. Sound:Beep. There are operation videos below, which can be watched in detail.
- remind:Do not use this item near explosive gas, vapor or dust. When pressing the power switch (Note: or shaking), the battery current will be directly conducted to the pen tip, which may cause Sparks can be caused when touching the ground or certain circuits. Do not use the device under 11o/220V indoor current, only for DC6~24V systemThere are detailed instructions in the product box, please refer to the operation.