{"id":7177701589172,"title":"WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V)","handle":"wowoone-1pc-pwm-to-voltage-module-0-100-pwm-converted-to-0-10v-voltage-suitable-for-signal-interface-switching-for-plc-or-other-industrial-control-boardspwm-to-voltage-0-10v","description":"\u003ch3\u003eWOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eParametersModule working voltage: DC 12V-30V; (current greater than 100mA)PWM\nsignal receiving frequency range: 1KHZ-3KHZPWM signal input level range:The\npeak-to-peak value is 4.5V to 10V, and the jumper cap is inserted at 5V. This\ntype of level signal is mainly for the conventional industrial control card,\n5V CPU interface;The peak-to-peak value is 12 to 24V, and the jumper cap is\ninserted at 24V. This type of level signal is mainly for the conventional PLC\ninterface.Conversion range: 0%-100% PWM conversion to 0-10V voltageAllowable\nerror: 5%Wiring instructionsVCC: Working power supply 12V-30V.GND: Working\npower ground.PWM: Input the positive end of the PWM signal.GND: Input signal\nnegative terminal.VOUT: Output voltage 0-10V.GND: Output voltage\nground.Instructions1, After power-on, when there is no input signal, the\noutput is 0V.2, For the first power-on, it is best to do a calibration debug:\nfind a 50% duty cycle signal to the PWM, GND, the amplitude corresponds to the\ncorresponding jumper. The frequency is 1KHZ-3KHZ. 3, Use a multimeter to\nmeasure the two ports VOUT and GND. At this time, the meter is displayed at\nabout 5V. Adjust the potentiometer on the board so that the multimeter is\ndisplayed at 5.00v. This calibrates your pulse signal with this module. 4,\nWhen the frequency changes, the correspondence may be offset and needs to be\nrecalibrated. The output voltage can be adjusted by adjusting the duty cycle.\nAccuracy can be controlled by adjusting the potentiometer.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eUsing MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.\u003c\/li\u003e\n \u003cli\u003eThe PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.\u003c\/li\u003e\n \u003cli\u003eSelect the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.\u003c\/li\u003e\n \u003cli\u003eModule working voltage: DC 12V-30V; (current greater than 100mA)\u003c\/li\u003e\n \u003cli\u003ePWM signal receiving frequency range: 1KHZ-3KHZ\u003c\/li\u003e\n \u003c\/ul\u003e\n\n","published_at":"2022-07-02T04:26:54+10:00","created_at":"2022-07-02T04:26:58+10:00","vendor":"WOWOONE","type":"Controls","tags":["industrial"],"price":8400,"price_min":8400,"price_max":8400,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":41625833275572,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B08JTDJXLY","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V)","public_title":null,"options":["Default Title"],"price":8400,"weight":9,"compare_at_price":null,"inventory_management":null,"barcode":"0046432415135","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/auspowers.com\/cdn\/shop\/products\/B08JTDJXLY.jpg?v=1656744275","\/\/auspowers.com\/cdn\/shop\/products\/61goFZWufHL.jpg?v=1656700018","\/\/auspowers.com\/cdn\/shop\/products\/51dXDxcc8tL.jpg?v=1656700018","\/\/auspowers.com\/cdn\/shop\/products\/61l5ZtokKaL.jpg?v=1656700018"],"featured_image":"\/\/auspowers.com\/cdn\/shop\/products\/B08JTDJXLY.jpg?v=1656744275","options":["Title"],"media":[{"alt":"[Australia - AusPower] - WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V) ","id":26375942045876,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/B08JTDJXLY.jpg?v=1656744275"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/B08JTDJXLY.jpg?v=1656744275","width":1000},{"alt":"[Australia - AusPower] - WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V) ","id":26371019899060,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61goFZWufHL.jpg?v=1656700018"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61goFZWufHL.jpg?v=1656700018","width":1000},{"alt":"[Australia - AusPower] - WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V) ","id":26371019931828,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/51dXDxcc8tL.jpg?v=1656700018"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/51dXDxcc8tL.jpg?v=1656700018","width":1000},{"alt":"[Australia - AusPower] - WOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V) ","id":26371019964596,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61l5ZtokKaL.jpg?v=1656700018"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61l5ZtokKaL.jpg?v=1656700018","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003eWOWOONE 1PC PWM to Voltage Module 0%-100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control Boards(PWM-to-Voltage 0-10V)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eParametersModule working voltage: DC 12V-30V; (current greater than 100mA)PWM\nsignal receiving frequency range: 1KHZ-3KHZPWM signal input level range:The\npeak-to-peak value is 4.5V to 10V, and the jumper cap is inserted at 5V. This\ntype of level signal is mainly for the conventional industrial control card,\n5V CPU interface;The peak-to-peak value is 12 to 24V, and the jumper cap is\ninserted at 24V. This type of level signal is mainly for the conventional PLC\ninterface.Conversion range: 0%-100% PWM conversion to 0-10V voltageAllowable\nerror: 5%Wiring instructionsVCC: Working power supply 12V-30V.GND: Working\npower ground.PWM: Input the positive end of the PWM signal.GND: Input signal\nnegative terminal.VOUT: Output voltage 0-10V.GND: Output voltage\nground.Instructions1, After power-on, when there is no input signal, the\noutput is 0V.2, For the first power-on, it is best to do a calibration debug:\nfind a 50% duty cycle signal to the PWM, GND, the amplitude corresponds to the\ncorresponding jumper. The frequency is 1KHZ-3KHZ. 3, Use a multimeter to\nmeasure the two ports VOUT and GND. At this time, the meter is displayed at\nabout 5V. Adjust the potentiometer on the board so that the multimeter is\ndisplayed at 5.00v. This calibrates your pulse signal with this module. 4,\nWhen the frequency changes, the correspondence may be offset and needs to be\nrecalibrated. The output voltage can be adjusted by adjusting the duty cycle.\nAccuracy can be controlled by adjusting the potentiometer.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eUsing MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.\u003c\/li\u003e\n \u003cli\u003eThe PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.\u003c\/li\u003e\n \u003cli\u003eSelect the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.\u003c\/li\u003e\n \u003cli\u003eModule working voltage: DC 12V-30V; (current greater than 100mA)\u003c\/li\u003e\n \u003cli\u003ePWM signal receiving frequency range: 1KHZ-3KHZ\u003c\/li\u003e\n \u003c\/ul\u003e\n\n"}