{"id":7246472642740,"title":"HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560","handle":"hiletgo-stackable-sd-card-tf-card-micro-sd-card-sd-sdhc-micro-sd-micro-sdhc-card-reader-shield-multi-functional-sd-card-shield-module-for-arduino-uno-r3-mega2560","description":" \u003ch1\u003eHiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560\u003c\/h1\u003e\n \u003ch3\u003e\n\u003cspan class=\"glyphicon glyphicon-list-alt\"\u003e\u003c\/span\u003e Description\u003c\/h3\u003e\n \u003cp\u003eFeatures: Compatible SD card, Micro SD card and SDHC card\nsupportable.Prototype expand Library support Size: 53mm x 47mm Weight: 35g Pin\nWith SD Card 5V VCC ---3v3 GND--GND D13---SD_CLK D12-- SD_OUT D11---SD_IN D10\n--SD_CS 1.The shield is missing pins for SCL and SDA If you need those two for\nI2C communication like a display shield, you have to use Analog pin 4 and\nAnalog pin 52. How to build an eeprom programmer to program 2708s for\ncomputer?A: Set the switch to \"3.3\"and pressed on, SD cards require 3.3v or\nyou could damage them.B:Installed the shield on a Mega 2560 R3 if you need lot\nof I\/O pins forprom programmer,You can plug any shield, in general, into any\nArduino as long as you \"match\" up the pins which are marked.C: Installed the\nshield on Mega,put the shield on the Duemilanove, changed the chip select pin\nto \"10\" again, and Cardinfo ran. Note that when you compile using the IDE, you\nhave to CHANGE the target board to the board you are using or it just won't\nwork.D:when you modify the code, make sure that you replace \"10\" with \"53\".\n3.You can by googling \"\"SD shield 3.0\"\" and clicking on the iTEAD wiki link.\nA-Put the SD shield on whatever arduino you have. Using the labels on the\nshield and arduino, make sure the pins match.B-Use the wiki instructions'\n\"Compatibility\" section to find out what position the 3.3V\/5V selector switch\nshould be in, and whether you need to remove ALL 3 of the adjacent SPI Jumpers\non the top of the board given the arduino board you're using. For the arduino\nDUE,you can remove these jumpers and keep the switch on 3.3V.\u003c\/p\u003e\n \u003cp\u003eFeatures:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eThis SD card shield is a standard SD card \/ TF card break out board for Arduino. The SD card shield adds storage to your Arduino project.\u003c\/li\u003e\n\u003cli\u003eStackable SD Card Shield is a stackable design SD \/ TF card expansion board. It supports direct insertion in the Arduino board to extend SD \/ TF read and write functions.\u003c\/li\u003e\n\u003cli\u003eSD \/ TF card expansion board uses the hardware ISP interface, so only supports SIP mode SD \/ TF card.\u003c\/li\u003e\n\u003cli\u003eThis expansion board uses only a handful of pins, so the stack design allows you to plug in another expansion board on this board, provided that the same SPI pins are not used, such as Bluetooth expansion board, GPRS expansion board.\u003c\/li\u003e\n\u003cli\u003eMany electronic enthusiasts have provided a simple documentation program for Arduino. And we provide a simple TinyFAT file system library, you can easily achieve control SD \/ TF card reader - this library only supports FAT16 small capacity card, such as 1G card, if you need to support FAT32, you can use Official library for Arduino.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n ","published_at":"2022-09-02T05:46:26+10:00","created_at":"2022-09-02T05:46:32+10:00","vendor":"HiLetgo","type":"Memory Card Readers","tags":["electronics3"],"price":9000,"price_min":9000,"price_max":9000,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":41819301052596,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B006LRR0IQ","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560","public_title":null,"options":["Default Title"],"price":9000,"weight":41,"compare_at_price":null,"inventory_management":null,"barcode":"610708262626","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/auspowers.com\/cdn\/shop\/products\/B006LRR0IQ.jpg?v=1662103847","\/\/auspowers.com\/cdn\/shop\/products\/61InFO2qdiL.jpg?v=1662061592","\/\/auspowers.com\/cdn\/shop\/products\/61fctKhUjGL.jpg?v=1662061592","\/\/auspowers.com\/cdn\/shop\/products\/61tj2Kfmf8L.jpg?v=1662061592","\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_d3971072-106a-4bc4-8633-ed008b40d1a7.jpg?v=1662061592"],"featured_image":"\/\/auspowers.com\/cdn\/shop\/products\/B006LRR0IQ.jpg?v=1662103847","options":["Title"],"media":[{"alt":"[Australia - AusPower] - HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560 ","id":27025548116148,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1200,"width":1200,"src":"\/\/auspowers.com\/cdn\/shop\/products\/B006LRR0IQ.jpg?v=1662103847"},"aspect_ratio":1.0,"height":1200,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/B006LRR0IQ.jpg?v=1662103847","width":1200},{"alt":"[Australia - AusPower] - HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560 ","id":27021072040116,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1200,"width":1200,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61InFO2qdiL.jpg?v=1662061592"},"aspect_ratio":1.0,"height":1200,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61InFO2qdiL.jpg?v=1662061592","width":1200},{"alt":"[Australia - AusPower] - HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560 ","id":27021072072884,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1200,"width":1200,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61fctKhUjGL.jpg?v=1662061592"},"aspect_ratio":1.0,"height":1200,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61fctKhUjGL.jpg?v=1662061592","width":1200},{"alt":"[Australia - AusPower] - HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560 ","id":27021072105652,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1200,"width":1200,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61tj2Kfmf8L.jpg?v=1662061592"},"aspect_ratio":1.0,"height":1200,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61tj2Kfmf8L.jpg?v=1662061592","width":1200},{"alt":"[Australia - AusPower] - HiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560 ","id":27021072138420,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1100,"width":1100,"src":"\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_d3971072-106a-4bc4-8633-ed008b40d1a7.jpg?v=1662061592"},"aspect_ratio":1.0,"height":1100,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_d3971072-106a-4bc4-8633-ed008b40d1a7.jpg?v=1662061592","width":1100}],"requires_selling_plan":false,"selling_plan_groups":[],"content":" \u003ch1\u003eHiLetgo Stackable SD Card TF Card Micro SD Card SD\/SDHC\/Micro SD\/Micro SDHC Card Reader Shield Multi-Functional SD Card Shield Module for Arduino UNO R3 MEGA2560\u003c\/h1\u003e\n \u003ch3\u003e\n\u003cspan class=\"glyphicon glyphicon-list-alt\"\u003e\u003c\/span\u003e Description\u003c\/h3\u003e\n \u003cp\u003eFeatures: Compatible SD card, Micro SD card and SDHC card\nsupportable.Prototype expand Library support Size: 53mm x 47mm Weight: 35g Pin\nWith SD Card 5V VCC ---3v3 GND--GND D13---SD_CLK D12-- SD_OUT D11---SD_IN D10\n--SD_CS 1.The shield is missing pins for SCL and SDA If you need those two for\nI2C communication like a display shield, you have to use Analog pin 4 and\nAnalog pin 52. How to build an eeprom programmer to program 2708s for\ncomputer?A: Set the switch to \"3.3\"and pressed on, SD cards require 3.3v or\nyou could damage them.B:Installed the shield on a Mega 2560 R3 if you need lot\nof I\/O pins forprom programmer,You can plug any shield, in general, into any\nArduino as long as you \"match\" up the pins which are marked.C: Installed the\nshield on Mega,put the shield on the Duemilanove, changed the chip select pin\nto \"10\" again, and Cardinfo ran. Note that when you compile using the IDE, you\nhave to CHANGE the target board to the board you are using or it just won't\nwork.D:when you modify the code, make sure that you replace \"10\" with \"53\".\n3.You can by googling \"\"SD shield 3.0\"\" and clicking on the iTEAD wiki link.\nA-Put the SD shield on whatever arduino you have. Using the labels on the\nshield and arduino, make sure the pins match.B-Use the wiki instructions'\n\"Compatibility\" section to find out what position the 3.3V\/5V selector switch\nshould be in, and whether you need to remove ALL 3 of the adjacent SPI Jumpers\non the top of the board given the arduino board you're using. For the arduino\nDUE,you can remove these jumpers and keep the switch on 3.3V.\u003c\/p\u003e\n \u003cp\u003eFeatures:\u003c\/p\u003e\n \u003cul\u003e\n \u003cli\u003eThis SD card shield is a standard SD card \/ TF card break out board for Arduino. The SD card shield adds storage to your Arduino project.\u003c\/li\u003e\n\u003cli\u003eStackable SD Card Shield is a stackable design SD \/ TF card expansion board. It supports direct insertion in the Arduino board to extend SD \/ TF read and write functions.\u003c\/li\u003e\n\u003cli\u003eSD \/ TF card expansion board uses the hardware ISP interface, so only supports SIP mode SD \/ TF card.\u003c\/li\u003e\n\u003cli\u003eThis expansion board uses only a handful of pins, so the stack design allows you to plug in another expansion board on this board, provided that the same SPI pins are not used, such as Bluetooth expansion board, GPRS expansion board.\u003c\/li\u003e\n\u003cli\u003eMany electronic enthusiasts have provided a simple documentation program for Arduino. And we provide a simple TinyFAT file system library, you can easily achieve control SD \/ TF card reader - this library only supports FAT16 small capacity card, such as 1G card, if you need to support FAT32, you can use Official library for Arduino.\u003c\/li\u003e\n \u003c\/ul\u003e\n\n\n "}