{"id":7086858240180,"title":"HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560","handle":"hiletgo-4pcs-l298n-motor-driver-controller-board-module-stepper-motor-dc-dual-h-bridge-for-arduino-smart-car-power-uno-mega-r3-mega2560","description":"\u003ch3\u003eHiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eSpecification: Chip: ST L298N dual H-bridge driver chip Logic voltage: 5V\nLogic current 0mA-36mA Storage Temperature: -20 ¡æ to +135 ¡æ Operating mode:\nH-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single\nbridge) Maximum power: 25W Driver Board Size:55mm60mm30mm Driver Board\nWeight:33g Dimensions: 43x43x27mm Note: .General Application: When your driver\nis 7V-12V, you can enable the on-board 5V logic supply. When using the on-\nboard 5V power supply, the + 5V power supply in the interface does not input\nvoltage, but it can draw 5V voltage for external use. .Unconventional\napplication of high-voltage drive: When the driving voltage is higher than\n12V, less than or equal to 24V, for example, to drive a motor with rated\nvoltage of 18V, the jumper cap with 5V output enabled on-board voltage must be\npulled out and then outside the 5V output port Connect 5V voltage to L298N\ninternal logic voltage supply. Package Included: 4 L298N Motor Driver\ncontroller Board ModuleThere are two ways to turn the system back on:1. flip\nthe power switch on the back of the computer and wait for the power supply cap\nto discharge as the relay will reset without power.2.after popping the hood\nand examining for faults, press the button on the relay.There is a red LED on\nthis for power and a green LED to indicate the relay is activated, so you can\nbe pretty sure what state this is in .Any time you are trying to hot wire an\nATX power supply and you need a toggle function besides the switch in the\nback, just needs power from pin 9, the relay connected to pin 16 and then of\ncourse connections back to ground pin(s).\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eL298N as main driver chip makes strong driving ability\/small heating\/strong anti-interference\/low calorific value\u003c\/li\u003e\n \u003cli\u003eDual-channel H-bridge driver working mode creates higher working efficiency\u003c\/li\u003e\n \u003cli\u003eTo avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage\u003c\/li\u003e\n \u003cli\u003eLarge capacity filter capacitance, afterflow protection diode, more stable and reliable\u003c\/li\u003e\n \u003c\/ul\u003e\n\n","published_at":"2022-03-19T05:35:04+11:00","created_at":"2022-03-19T05:35:04+11:00","vendor":"HiLetgo","type":"Motor Speed Controllers","tags":["auspowers_batchone"],"price":9900,"price_min":9900,"price_max":9900,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":41336032886964,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B07BK1QL5T","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560","public_title":null,"options":["Default Title"],"price":9900,"weight":130,"compare_at_price":null,"inventory_management":null,"barcode":"3-01-0032-4PCS","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/auspowers.com\/cdn\/shop\/products\/B07BK1QL5T.jpg?v=1648583499","\/\/auspowers.com\/cdn\/shop\/products\/61GlUbv0PeL.jpg?v=1647628505","\/\/auspowers.com\/cdn\/shop\/products\/61YkASUO-2L.jpg?v=1647628505","\/\/auspowers.com\/cdn\/shop\/products\/61rz1SeJ_WL.jpg?v=1647628505","\/\/auspowers.com\/cdn\/shop\/products\/71jbtN-VE2L.jpg?v=1647628505","\/\/auspowers.com\/cdn\/shop\/products\/71DaD5L6L9L.jpg?v=1647628505","\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_f51ed0a1-863e-4b9e-b38e-f54564ef6307.jpg?v=1647628505"],"featured_image":"\/\/auspowers.com\/cdn\/shop\/products\/B07BK1QL5T.jpg?v=1648583499","options":["Title"],"media":[{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25352123154612,"position":1,"preview_image":{"aspect_ratio":1.0,"height":1200,"width":1200,"src":"\/\/auspowers.com\/cdn\/shop\/products\/B07BK1QL5T.jpg?v=1648583499"},"aspect_ratio":1.0,"height":1200,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/B07BK1QL5T.jpg?v=1648583499","width":1200},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705141428,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61GlUbv0PeL.jpg?v=1647628505"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61GlUbv0PeL.jpg?v=1647628505","width":1000},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705174196,"position":3,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61YkASUO-2L.jpg?v=1647628505"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61YkASUO-2L.jpg?v=1647628505","width":1000},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705206964,"position":4,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/61rz1SeJ_WL.jpg?v=1647628505"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/61rz1SeJ_WL.jpg?v=1647628505","width":1000},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705239732,"position":5,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/71jbtN-VE2L.jpg?v=1647628505"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/71jbtN-VE2L.jpg?v=1647628505","width":1000},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705272500,"position":6,"preview_image":{"aspect_ratio":1.25,"height":819,"width":1024,"src":"\/\/auspowers.com\/cdn\/shop\/products\/71DaD5L6L9L.jpg?v=1647628505"},"aspect_ratio":1.25,"height":819,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/71DaD5L6L9L.jpg?v=1647628505","width":1024},{"alt":"[Australia - AusPower] - HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560 ","id":25207705305268,"position":7,"preview_image":{"aspect_ratio":1.0,"height":1100,"width":1100,"src":"\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_f51ed0a1-863e-4b9e-b38e-f54564ef6307.jpg?v=1647628505"},"aspect_ratio":1.0,"height":1100,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/51_Du5sRIiL_f51ed0a1-863e-4b9e-b38e-f54564ef6307.jpg?v=1647628505","width":1100}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003eHiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eSpecification: Chip: ST L298N dual H-bridge driver chip Logic voltage: 5V\nLogic current 0mA-36mA Storage Temperature: -20 ¡æ to +135 ¡æ Operating mode:\nH-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single\nbridge) Maximum power: 25W Driver Board Size:55mm60mm30mm Driver Board\nWeight:33g Dimensions: 43x43x27mm Note: .General Application: When your driver\nis 7V-12V, you can enable the on-board 5V logic supply. When using the on-\nboard 5V power supply, the + 5V power supply in the interface does not input\nvoltage, but it can draw 5V voltage for external use. .Unconventional\napplication of high-voltage drive: When the driving voltage is higher than\n12V, less than or equal to 24V, for example, to drive a motor with rated\nvoltage of 18V, the jumper cap with 5V output enabled on-board voltage must be\npulled out and then outside the 5V output port Connect 5V voltage to L298N\ninternal logic voltage supply. Package Included: 4 L298N Motor Driver\ncontroller Board ModuleThere are two ways to turn the system back on:1. flip\nthe power switch on the back of the computer and wait for the power supply cap\nto discharge as the relay will reset without power.2.after popping the hood\nand examining for faults, press the button on the relay.There is a red LED on\nthis for power and a green LED to indicate the relay is activated, so you can\nbe pretty sure what state this is in .Any time you are trying to hot wire an\nATX power supply and you need a toggle function besides the switch in the\nback, just needs power from pin 9, the relay connected to pin 16 and then of\ncourse connections back to ground pin(s).\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eL298N as main driver chip makes strong driving ability\/small heating\/strong anti-interference\/low calorific value\u003c\/li\u003e\n \u003cli\u003eDual-channel H-bridge driver working mode creates higher working efficiency\u003c\/li\u003e\n \u003cli\u003eTo avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage\u003c\/li\u003e\n \u003cli\u003eLarge capacity filter capacitance, afterflow protection diode, more stable and reliable\u003c\/li\u003e\n \u003c\/ul\u003e\n\n"}

HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560

In Stock. Leaves warehouse within 2 - 3 business days

$99.00 AUD
Maximum quantity available reached.
Free Shipping Australia Wide
100% Safe & Secure Checkout
100 Days Return Policy *
1 Year Warranty *

HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560

Specification: Chip: ST L298N dual H-bridge driver chip Logic voltage: 5V Logic current 0mA-36mA Storage Temperature: -20 ¡æ to +135 ¡æ Operating mode: H-bridge driver (dual) Drive voltage: 5V-35V Drive current: 2A (MAX single bridge) Maximum power: 25W Driver Board Size:55mm60mm30mm Driver Board Weight:33g Dimensions: 43x43x27mm Note: .General Application: When your driver is 7V-12V, you can enable the on-board 5V logic supply. When using the on- board 5V power supply, the + 5V power supply in the interface does not input voltage, but it can draw 5V voltage for external use. .Unconventional application of high-voltage drive: When the driving voltage is higher than 12V, less than or equal to 24V, for example, to drive a motor with rated voltage of 18V, the jumper cap with 5V output enabled on-board voltage must be pulled out and then outside the 5V output port Connect 5V voltage to L298N internal logic voltage supply. Package Included: 4 L298N Motor Driver controller Board ModuleThere are two ways to turn the system back on:1. flip the power switch on the back of the computer and wait for the power supply cap to discharge as the relay will reset without power.2.after popping the hood and examining for faults, press the button on the relay.There is a red LED on this for power and a green LED to indicate the relay is activated, so you can be pretty sure what state this is in .Any time you are trying to hot wire an ATX power supply and you need a toggle function besides the switch in the back, just needs power from pin 9, the relay connected to pin 16 and then of course connections back to ground pin(s).

Product Features

  • L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value
  • Dual-channel H-bridge driver working mode creates higher working efficiency
  • To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
  • Large capacity filter capacitance, afterflow protection diode, more stable and reliable

Related Products