{"id":7086412366004,"title":"242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5)","handle":"242-viton-o-ring-90a-durometer-round-black-4-id-4-1-4-od-1-8-width-pack-of-5","description":"\u003ch3\u003e242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eThis O-ring is made of black Viton and has a durometer of 90A, a round cross-\nsection, and can be used across a wide temperature range (-15 degrees F \/-26\ndegrees C to 400 degrees F\/ 205 degrees C). Designed for use in a wide variety\nof sealing applications, this Viton O-ring meets standards defined by\nAerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.\nViton (fluorocarbon elastomer) has heat, fuel, and chemical resistance and is\ncompatible for use with non-flammable hydraulic fuels, silicone oil,\nchlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons\n(benzene) and aliphatic hydrocarbons (propane), as well as high vacuum\nenvironments, ozone, and weathering. Viton is vulnerable to low molecular\norganic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and\nsuper-heated steam. The durometer hardness of this Viton O-ring is 90A.\nDurometers measure the hardness of a material and its resistance to permanent\nindentation. A higher durometer value indicates greater resistance to\nindentation. On a scale of 0 to 100, a value of 0 indicates that a sample was\ncompletely penetrated, while a value of 100 shows no indentation in the\nsample. The letter following the number identifies the shore scale, which is\neither shore A or D. Shore A is used for softer plastics, while shore D is\nused for harder plastics. O-rings provide a pressure and fluid seal between\ncylindrically shaped, overlapping mating surfaces and are commonly seen in\nengines, faucets, flanges, valves, and various cylinders. They are circular in\nshape, with a round cross section, and a hole in the center, similar to a\ndoughnut. O-rings are available in various AS568A dash sizes, which is the\nstandardized sizing for O-rings, and defines the nominal inside diameter (ID),\nouter diameter (OD), and cross-sectional (CS) diameter of an O-ring.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eMade of Viton (fluorocarbon elastomer) for use with a variety of chemicals and fuels\u003c\/li\u003e\n \u003cli\u003eDurometer (hardness) of 90A for resistance to penetration\u003c\/li\u003e\n \u003cli\u003eRound cross-section to provide a seal between cylindrical overlapping surfaces\u003c\/li\u003e\n \u003cli\u003eFor use across a wide temperature range from -15 degrees F\/-26 degrees C to 400 degrees F\/ 205 degrees C\u003c\/li\u003e\n \u003cli\u003eMeets standards defined by Aerospace Standard AS568A\u003c\/li\u003e\n \u003c\/ul\u003e\n\n","published_at":"2022-03-18T23:34:39+11:00","created_at":"2022-03-18T23:34:39+11:00","vendor":"Mr O-Ring","type":"O-Rings","tags":["auspowers_batchone"],"price":10300,"price_min":10300,"price_max":10300,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":41334935584948,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"B0051Y2GNO","requires_shipping":true,"taxable":true,"featured_image":null,"available":true,"name":"242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5)","public_title":null,"options":["Default Title"],"price":10300,"weight":34,"compare_at_price":null,"inventory_management":null,"barcode":"742839450327","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/auspowers.com\/cdn\/shop\/products\/B0051Y2GNO.jpg?v=1648568812","\/\/auspowers.com\/cdn\/shop\/products\/51bid7qjm5L_22b6890e-b100-470c-8360-2e0732f7a8a5.jpg?v=1647606879"],"featured_image":"\/\/auspowers.com\/cdn\/shop\/products\/B0051Y2GNO.jpg?v=1648568812","options":["Title"],"media":[{"alt":"[Australia - AusPower] - 242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5) ","id":25349269815476,"position":1,"preview_image":{"aspect_ratio":2.244,"height":743,"width":1667,"src":"\/\/auspowers.com\/cdn\/shop\/products\/B0051Y2GNO.jpg?v=1648568812"},"aspect_ratio":2.244,"height":743,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/B0051Y2GNO.jpg?v=1648568812","width":1667},{"alt":"[Australia - AusPower] - 242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5) ","id":25203727073460,"position":2,"preview_image":{"aspect_ratio":1.0,"height":1000,"width":1000,"src":"\/\/auspowers.com\/cdn\/shop\/products\/51bid7qjm5L_22b6890e-b100-470c-8360-2e0732f7a8a5.jpg?v=1647606879"},"aspect_ratio":1.0,"height":1000,"media_type":"image","src":"\/\/auspowers.com\/cdn\/shop\/products\/51bid7qjm5L_22b6890e-b100-470c-8360-2e0732f7a8a5.jpg?v=1647606879","width":1000}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003ch3\u003e242 Viton O-Ring, 90A Durometer, Round, Black, 4\" ID, 4-1\/4\" OD, 1\/8\" Width (Pack of 5)\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eThis O-ring is made of black Viton and has a durometer of 90A, a round cross-\nsection, and can be used across a wide temperature range (-15 degrees F \/-26\ndegrees C to 400 degrees F\/ 205 degrees C). Designed for use in a wide variety\nof sealing applications, this Viton O-ring meets standards defined by\nAerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.\nViton (fluorocarbon elastomer) has heat, fuel, and chemical resistance and is\ncompatible for use with non-flammable hydraulic fuels, silicone oil,\nchlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons\n(benzene) and aliphatic hydrocarbons (propane), as well as high vacuum\nenvironments, ozone, and weathering. Viton is vulnerable to low molecular\norganic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and\nsuper-heated steam. The durometer hardness of this Viton O-ring is 90A.\nDurometers measure the hardness of a material and its resistance to permanent\nindentation. A higher durometer value indicates greater resistance to\nindentation. On a scale of 0 to 100, a value of 0 indicates that a sample was\ncompletely penetrated, while a value of 100 shows no indentation in the\nsample. The letter following the number identifies the shore scale, which is\neither shore A or D. Shore A is used for softer plastics, while shore D is\nused for harder plastics. O-rings provide a pressure and fluid seal between\ncylindrically shaped, overlapping mating surfaces and are commonly seen in\nengines, faucets, flanges, valves, and various cylinders. They are circular in\nshape, with a round cross section, and a hole in the center, similar to a\ndoughnut. O-rings are available in various AS568A dash sizes, which is the\nstandardized sizing for O-rings, and defines the nominal inside diameter (ID),\nouter diameter (OD), and cross-sectional (CS) diameter of an O-ring.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n \u003cul class=\"a\"\u003e\n \u003cli\u003eMade of Viton (fluorocarbon elastomer) for use with a variety of chemicals and fuels\u003c\/li\u003e\n \u003cli\u003eDurometer (hardness) of 90A for resistance to penetration\u003c\/li\u003e\n \u003cli\u003eRound cross-section to provide a seal between cylindrical overlapping surfaces\u003c\/li\u003e\n \u003cli\u003eFor use across a wide temperature range from -15 degrees F\/-26 degrees C to 400 degrees F\/ 205 degrees C\u003c\/li\u003e\n \u003cli\u003eMeets standards defined by Aerospace Standard AS568A\u003c\/li\u003e\n \u003c\/ul\u003e\n\n"}

242 Viton O-Ring, 90A Durometer, Round, Black, 4" ID, 4-1/4" OD, 1/8" Width (Pack of 5)

In Stock. Leaves warehouse within 2 - 3 business days

$103.00 AUD
Maximum quantity available reached.
Free Shipping Australia Wide
100% Safe & Secure Checkout
100 Days Return Policy *
1 Year Warranty *

242 Viton O-Ring, 90A Durometer, Round, Black, 4" ID, 4-1/4" OD, 1/8" Width (Pack of 5)

This O-ring is made of black Viton and has a durometer of 90A, a round cross- section, and can be used across a wide temperature range (-15 degrees F /-26 degrees C to 400 degrees F/ 205 degrees C). Designed for use in a wide variety of sealing applications, this Viton O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Viton (fluorocarbon elastomer) has heat, fuel, and chemical resistance and is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane), as well as high vacuum environments, ozone, and weathering. Viton is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam. The durometer hardness of this Viton O-ring is 90A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.

Product Features

  • Made of Viton (fluorocarbon elastomer) for use with a variety of chemicals and fuels
  • Durometer (hardness) of 90A for resistance to penetration
  • Round cross-section to provide a seal between cylindrical overlapping surfaces
  • For use across a wide temperature range from -15 degrees F/-26 degrees C to 400 degrees F/ 205 degrees C
  • Meets standards defined by Aerospace Standard AS568A

Related Products