{"product_id":"wengart-installation-contactor-25a-2no2nc-for-electricians-for-safe-priority-switching-without-risk-of-short-circuit-with-compact-36-mm-width-and-hum-free-ac-24-v-coil","title":"Wengart Installation contactor 25A 2NO2NC for electricians for safe priority switching without risk of short circuit with compact 36 mm width and hum-free AC 24 V coil","description":"\u003ch3\u003eWengart Installation contactor 25A 2NO2NC for electricians for safe priority switching without risk of short circuit with compact 36 mm width and hum-free AC 24 V coil\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eWengart WCT-25 (2NO+2NC): intelligent load switching and dual low voltage\nswitching competence. The modular Wengart household AC contactor (36 mm\nhousing width) is a heavy-duty control cabinet switching device according to\nthe international test standard IEC\/EN 61095. Designed for professional use in\nself-sufficient PV isolated systems, modern climate controls, intelligent heat\npump systems (such as SG-ready switches) as well as for complex control\nnetworks in the smart home, this four-pole in-line installation device offers\nuncompromising performance. Thanks to the robust internal mechanism, it is\nvalidated for safe operation in a wide temperature range from -20°C to +60°C\nat an insulation voltage of $U_i$ 500V. The anti-return guide: observe the 2NO\n+ 2NC mixing configuration! By far the most common reason for mispurchases and\nunwanted marketplace returns for modular shooters on mobile devices is the\nmisunderstanding of asymmetric contact assignment. Please check your switching\nmatrix before purchasing: this device has two contact contacts (2NO) and two\nopener contacts (2NC). It is not a standard 4NO contactor for simultaneously\nswitching on 3-phase loads! This means that as long as there is no current at\nthe control coil, the two NC paths are closed and the two NO paths are open.\nAs soon as you apply AC 24 V control voltage, this condition reverses at the\nsame time (change\/lock function). A careless connection of all phases to the\nseparate load paths leads to a fatal short circuit when switching. This short\npre-check protects your system from serious incorrect installations. Important\nnote on acoustics: hum-free permanent hold with clear switching clicks. A\ncommon pain point for control cabinet components are false expectations of\noperating noise in the immediate living area. This Wengart contactor has been\nacoustically optimised twofold: when tightened, the AC solenoid operates\ncompletely silently thanks to integrated short circuit rings and free from\nannoying mains hum (humm-free). However, since the contactor is designed for\ncurrents up to 25A, the inner mechanism has strong contact springs. When\nswitched on and off (11.5 VA switch-on power), the device therefore produces a\nclear, crisp mechanical switching noise. This tactile feedback is ideal for\ncontrol cabinets in technical rooms, garages, cellars or carports - it is not\nrecommended for bedrooms where absolute silence in the switching moment is\nrequired. Precise terminal specifications and important installation practice\ntip The performance terminals hold rigid copper conductors from 1.5 to 6$mm^2$\n(or flexible cables with ferrules from 1 to 4$mm^2$) at a recommended\nstripping length of 9mm. The clamps allow an exact tightening torque of up to\n0.8 N.m using a PZ1 screwdriver, which effectively minimises contact\nresistance. Please refer to the official installation layout according to\nindustry standards for permanent full load operation: if this contactor is\nmounted close to electronic controls (such as timers or thermostats), spacers\n(intermediate pieces in the 9mm pitch) must be inserted on both sides to\nensure optimal cross ventilation and prevent dangerous hotspots in the\nhousing. Technical data at a glance: Model: modular household AC contactor\n(2TE width). Compliance with standards: certified according to international\nstandard IEC\/EN 61095. Contact configuration: 4 pin \/ 2 NO (normal) + 2 NC\n(opener) \/ Case width: 36 mm Installation specification: snap mount for 35mm\nDIN rail (tilt angle up to $\\pm30^\\circ$) Coil control voltage ($U_c$): AC 24\nvolts AC (holding power: 3.0 VA \/ max. 1.3 W). Rated Operating Current\n($I_e$): Solid 25A (Class AC-7a) \/ Carrier 9A (Class AC-7b) Rated insulation\nvoltage ($U_i$): 500 V AC \/ shock voltage resistance ($U_{imp}$): type 2.5 kV\n(4kV at 24V) Terminal specification (main circuit): for cables from 1.5 to 6 $\nmm^2$ \/ maximum torque: 0.8 N.m Life index: 1,000,000 cycles mechanical \/\n100,000 cycles electric. Protection class of the housing: IP20 (IP40 after\ninstallation in the closed distribution housing).\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eSmart Home Low Voltage Controls with AC 24V AC: Completely eliminates costly coil fires due to incorrect current types in the system. The excitation winding is precisely designed for AC 24V (SELV-compliant) and works with 3.0 VA holding power in continuous operation.\u003c\/li\u003e\n         \u003cli\u003eTwo-way switching or locking of two unequal load paths: Prevents dangerous short circuits and returns due to incorrect contact assignments. The combined 2NO (normal) + 2NC (opener) architecture controls currents up to 25 A phase-offset to only 36 mm width.\u003c\/li\u003e\n         \u003cli\u003eAutomation of electric storage heaters or small fan motors: Eliminates the risk of premature contact burn due to high inrush currents. Switches pure ohmic heating loads up to massive 25 A (AC-7a) and inductive motor loads up to 9 A (AC-7b).\u003c\/li\u003e\n         \u003cli\u003eInstallation in decentralised distribution boxes, workshops or carports: saves tedious searching for manual system diagnostics in the event of a fault. This standard mechanical hardware delivers a crisp shift click as physical feedback and remains absolutely humm-free when holded.\u003c\/li\u003e\n         \u003cli\u003eDense DIN rail assembly in the central counter and fuse box: Ends assembly frustration with the safe wiring of flexible copper cables from 1 to 4 mm2. The PZ1 clamps allow an exact torque of 0.8 N.m for permanently fixed connections.\u003c\/li\u003e\n  \u003c\/ul\u003e","brand":"WENGART","offers":[{"title":"Default Title","offer_id":44374859546804,"sku":"de-B0CYSJHR61","price":159.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0595\/9906\/1172\/files\/B0CYSJHR61.jpg?v=1788266902","url":"https:\/\/auspowers.com\/products\/wengart-installation-contactor-25a-2no2nc-for-electricians-for-safe-priority-switching-without-risk-of-short-circuit-with-compact-36-mm-width-and-hum-free-ac-24-v-coil","provider":"AusPower Australia","version":"1.0","type":"link"}