{"product_id":"aideepen-step-up-converter-1200w-20a-dc-dc-boost-converter-constant-voltage-and-constant-current-adjustable-14-85v-to-14-120v-1200-w-20-a-upgrade","title":"Aideepen Step Up Converter, 1200W 20A DC-DC Boost Converter, Constant Voltage and Constant Current Adjustable 14-85V to 14-120V 1200 W 20 A (upgrade)","description":"\u003ch3\u003eAideepen Step Up Converter, 1200W 20A DC-DC Boost Converter, Constant Voltage and Constant Current Adjustable 14-85V to 14-120V\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eTo avoid damage to the product due to improper operation, please read the\ninstructions and precautions carefully before you buy\/use it. Upgrade\nfunction: different from the old model B0BZ4HXQLD 1. Adjustment of higher\ninput and output parameters. 2. The circuit is optimized, the output voltage\nis more stable and the switching MOS tube is quickly switched off and\ndischarged to prevent the risk of failure and short circuit of the MOS tube.\n3. The starting temperature of the fan decreases. 4. Power lines have been\nopened with sheet metal windows. 5. A constant resistance is added to the\noutput current detection to make excessive current more stable. 6. Equipped\nwith a fuse for securing. If the fuse burns out, you can replace it yourself.\nFeatures: 1. High Parameter Adjustment Support higher input and output voltage\nrange, suitable for a wider range of application scenarios. 2. Optimize\nCircuit Design Add a MOS tube to quickly shut off the circuit to prevent\nfailures and short circuits and improve safety. 3. Intelligent Under Voltage\nProtection The UVP potentiometer adjusts the undervoltage protection to\nprevent overload and damage to the power supply. 4. Constant Current Load\nAdjustment The CC potentiometer adjusts the output current, suitable for\nconstant current loads. 5. High Current Stability The circuit is opened with\ntin windows and constantan resistance detection to ensure stable operation at\nhigh current. Power on sequence for a boost power supply 1. First, adjust the\nundervoltage protection when idle. 2. Adjust the output voltage. (The output\nvoltage must only be higher than the input voltage.) 3. If you have a constant\ncurrent load (e.g. an LED lamp or battery), adjust the output current to the\nminimum, then connect the load and increase the current. The load voltage must\nbe higher than the input voltage of the boost power supply, and the power\nsupply must be operated in boost mode. (A 12V input can only charge batteries\nwith 24V or more, a 24V input only batteries with 36V or more.) 4. After\nadjusting voltage and current, first turn on the boost power supply and then\nconnect the load. Product parameters: Input voltage: DC 14-85V Output voltage:\nDC 14-120V (±5V), output 120V, input voltage must be above 20V Input Current:\n20A (Max) Output adjustment current: 1.5-18A (±0.5A) Input low voltage\nprotection range: 10-68V (±5V) Fan opening temperature: 40 degrees Input\nreverse polarity protection: yes. Typical efficiency (smaller input and output\npressure difference leads to higher efficiency): 90%-96% Size (including fan):\n130 x 52 x 62 mm. Please note: 1. The output is 120V and the input voltage\nmust be above 20V. 2. Try not to use the highest or lowest input and output\nvoltage. 3. The working current must not exceed the maximum input current of\nthe power supply. The working current is calculated by dividing the output\npower by the input voltage multiplied by 1.06 (1.06 is the loss of the power\nsupply). Example: Using the example of the 1200W model A, the input voltage is\n15V, the output 48V, output load current is 5A, 48V  5A\/15V  1.06=16.96A,\nthe operating current is less than 20A at this time and it can work normally.\nIf the load is 48V 7A, 48V7A\/15V1.06=23.75A and the operating current is\ngreater than the maximum input current of the power supply 20A, it cannot be\nused. 4. Regarding work efficiency: the smaller the difference between input\nand output voltage, the higher the efficiency, and the greater the voltage\ndifference, the lower the efficiency. When the input is 20V, the output is\n120V. At this time, the working efficiency is the lowest and is below 90%. The\npower of the input power supply must be more than 1.5 times the load. 5. It is\nstrictly prohibited to adjust the output current by short circuit. 6. Charging\nsuper capacitors is strictly prohibited. 7. The fan is temperature controlled\nand only rotates when the cooler temperature reaches about 40 degrees. A note\non performance: Take the 1200W booster as an example. Since the booster power\nsupply has an input current limit of 20A, there is no 1200W when the input\nvoltage is low. The input voltage is, for example, 14 V, 14 V x 20 A = 280 W.\nIn addition to the losses in current conversion, the maximum output power at\nan input voltage of 14V is about 250W, and it is not recommended to operate\nthe power supply under full load. Jianyi should not exceed 210W when entering\n14V To reach the maximum input voltage of the power supply, the input voltage\nmust be above 64V. Shipping list: 1 x power module. Accessories x1 (bolt,\ninsurance part).\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eParameters: Output power: 1200W; Input voltage range: 14-85V; Output voltage range: 14~120V; Input current: Max 20A; Output current: 1.5~18A (0.5A). (For upgrade, please refer to the description page.)\u003c\/li\u003e\n         \u003cli\u003eMultiple protection mechanisms: Equipped with input reverse polarity protection and undervoltage protection to ensure safe and worry-free use, it can be used for car battery amplification, battery charging, etc. Equipped with a replacement fuse that can be replaced and maintained by the user.\u003c\/li\u003e\n         \u003cli\u003eEfficient and stable: Optimise the circuit design and increase the quick shutdown of the MOS tube to ensure a more stable output voltage. Suitable for high power LED, motor, digital products, solar panel voltage regulator, etc.\u003c\/li\u003e\n         \u003cli\u003eIntelligent undervoltage protection: the UVP potentiometer adjusts the undervoltage protection to prevent overload and damage to the power supply. Constant Current Load Adjustment: CC potentiometer adjusts the output current, suitable for constant current loads.\u003c\/li\u003e\n         \u003cli\u003eNote: Try not to use the highest or lowest input and output voltage. It is strictly forbidden to change the output current by short circuit. Charging super capacitors is strictly prohibited. (If you have any questions, please contact us)\u003c\/li\u003e\n         \u003cli\u003eInstruction manual: Please enter all characters in brackets\u003c\/li\u003e\n  \u003c\/ul\u003e","brand":"Aideepen","offers":[{"title":"1200 W 20 A (upgrade)","offer_id":44374909026484,"sku":"de-B0DTK98BF3","price":194.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0595\/9906\/1172\/files\/B0DTK98BF3.jpg?v=1788267868","url":"https:\/\/auspowers.com\/products\/aideepen-step-up-converter-1200w-20a-dc-dc-boost-converter-constant-voltage-and-constant-current-adjustable-14-85v-to-14-120v-1200-w-20-a-upgrade","provider":"AusPower Australia","version":"1.0","type":"link"}