BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control Geekstory
BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control Geekstory
Specification Receiving Format : GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1 Channels : 72 Searching Channel Sensitivity Tracking : -167dBm, Reacquisition : -160dBm Cold start : -148dBm, Hot start : -156dBm Accuracy Position Horizontal : 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky) Velocity : 0.1m/sec 95% (SA off) Timing : 1us synchronized to GPS time Acquisition Time Cold Start : 26s, Warm start : 25s, Hot start : 1s Data and Update Rate Support Rate : 4800bps to 921600bps,Default 9600bps Data Level : TTL or RS-232,Default TTL level Data Protocol : NMEA-0183 or UBX, Default NMEA-0183 Single GNSS : 1Hz-18Hz Concurrent GNSS : 1Hz-10Hz,Default 1Hz Operational Limits Altitude : 50,000m Max, Velocity : 515m/s Max, Acceleration : Less than 4g Power consumption VCC : DC Voltage 3.0V-5.5V,Typical: 5.0V Current : Capture 50mA/5.0V Operating temp : -40 °C to +85°C Storage Temp : -40°C to +105°C Indicator: TX LED:blue.The data output, TX LED flashing PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed Wiring: GND,TX output,RX input,VCC(3.0v-5.5v) NMEA message output sample GNRMC,073114.00,A,2237.56240,N,11401.59614,E,1.329,21.11,020916,,,A,V37 GNVTG,21.11,T,,M,1.329,N,2.462,K,A1B GNGGA,073114.00,2237.56240,N,11401.59614,E,1,12,0.78,112.9,M,-2.5,M,,54 GNGSA,A,3,19,05,02,06,17,12,09,13,,,,,1.48,0.78,1.26,101 GNGSA,A,3,69,83,84,70,68,82,,,,,,,1.48,0.78,1.26,20E GPGSV,4,1,13,02,46,340,36,05,52,254,37,06,42,041,41,09,22,053,40,06E GPGSV,4,2,13,12,32,282,35,13,13,185,33,17,36,131,37,19,57,119,44,066 GPGSV,4,3,13,20,03,237,,23,00,038,,25,09,311,19,42,51,128,32,060 GPGSV,4,4,13,50,46,123,33,050 GLGSV,2,1,08,68,25,027,39,69,78,011,36,70,40,213,43,74,00,259,,078 GLGSV,2,2,08,82,06,124,36,83,46,085,44,84,44,358,41,85,05,324,14,074 GNGLL,2237.56240,N,11401.59614,E,073114.00,A,A7C BN 220 GPS connection to flight controller VCC to 5V RX to TX3 TX to RX3 GND to G betaflight Software Set up GPS module with betaflight Software BN 220 GPS connection to sensor RX to D4 TX to D3 GND to GND Read more BN-180 GPS BN-220 GPS BN-800 GPS BN-880 GPS Flash No 4M Flash 4M Flash 4M Flash Compass No No HMC5883L HMC5883L Antenna Type Passive Passive Passive Active Defaut Working Mode GPS+GLONASS GPS+GLONASS GPS+GLONASS GPS+GLONASS Voltage 3.6-5.5V 3.6-5.5V 3.6-5.5V 3.6-5.5V Default Baudrate 9600 9600 9600 9600 Frequency Range 1-10HZ 1-10HZ 1-10HZ 1-10HZ Output TTL TTL TTL TTL Pin Header GND,TX,RX,VCC GND,TX,RX,VCC SDA,GND,TX,RX,VCC,SCL SDA,GND,TX,RX,VCC,SCL Connector 1.0mm pitch 4P 1.0mm pitch 4P 1.25mm pitch 6P 1.25mm pitch 6P GPS Modules Comparison BN-180 GPS Module Size: 18186mm BN-220 GPS Module Size: 22206mm BN-880 GPS Module Size: 282810mm BN-800 GPS Module Size: 35356mm
Product Features
- BN-220 has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. If you need gps with flash and compass, please buy bn-880 from Geekstory.
- When you use it for Raspberry Pi, there is no driver needed but you need to install software
- The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place.
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
- The product documentation link cannot be displayed. If you need technical documentation, please click Geekstory(you can find "Sold by Geekstory" under Buy Now button), in the new page, click Ask a question to email us